Dyeing Your Own Silk Veil With Kool-Aid!

Supplies that I used in this project:

• UNDYED SILK VEIL
• PACKETS/CONTAINERS OF KOOL-AID THAT REQUIRE THAT SUGAR BE ADDED- This is SOOO important. Do NOT use the sugar free Kool-Aid or Kool-Aid that already has the sugar added. You want the citric acid and color, not the sugar which would make a royal sticky mess.
• SYNTHRAPOL
• PLASTIC WRAP
• MEASURING CUP
• MICROWAVE
• WASHING MACHINE
• CLOTHING IRON

1.  Rubber band fabric to separate areas of color if you're wanting clear demarcations between color shifts. I wanted a rainbow centered on my veil so I pinched the fabric at the center of the length, on one edge and placed a band at about 8" down, then continued banding down the length of the now sort of folded/pleated fabric. You could start at one end/corner  instead of in the middle to create a horizontal gradient or a diagonal gradient. You can also experiment with sprinkling dye into place for a textured visual effect.
2. Soak silk in apple cider vinegar. For this step I filled a mop bucket with vinegar and tossed my fabric in, poked it down so it was all submerged and left it there while I prepared the rest of my stuff.
3. Cover counter with long piece of cling wrap. I used one LONG piece that was about 6-8' long. This kept most of the Kool-Aid off my counter and later trapped the moisture and dye with the fabric while steaming.
4. Wring out silk and lay out on top of cling wrap. You don't want the fabric to be so full of vinegar that it can't absorb the Kool-Aid mixture. Bone dry, and the dye can't travel, too wet and the dye can't be absorbed.
5. Mix first Kool-Aid color with water (cherry). The idea is to make a thick syrup consistency. You could mix them all at once in separate cups but I was using my one liquid measuring cup so I just rinsed between colors.
6. Pour from measuring cup over fabric section. Be sure the drink powder is well mixed so that the liquid is of equal dye strength.
7. Scrunch to distribute dye. I just kind of worked the dye in a bit with my gloved fingers.
8. Mix, pour, scrunch each additional color

1. Fold cling wrap around fabric like a burrito and coil up, leaving a vent at end of coil for steam

1. Microwave for 1 minute, let sit one minute (total 4 minutes of heating time)

1. Carry VERY HOT fabric/plastic to wash machine filled with cold water and 2 caps of synthrapol
2.  Put untwisted end of plastic/fabric into machine, uncoil, and shake fabric gently from plastic into machine. The liquid dye will be pouring out with the fabric so the idea is to keep all the mess inside the wash machine to avoid awful cleanup chores ;)
3. Run normal cold water cycle
4. Air dry silk and then iron with steam on the silk setting. This should help set the dye.

Mord'Sith Hair Tutorial

Well friends I have finally gotten up the courage to make my first how-to video :) I had a few friends who were asking me how I did my hair for my Halloween costume this year so I thought I'd share my method. Previous methods that I had read about required the use of two synthetic braids but this method only requires one. Wore it last night when I went out dancing and not a hair came out of place! Please feel free to ask questions, ask for more how-to's or leave constructive comments!

T-shirt to Choli Conversion How-To

Don't ask me what the motivation was, I honestly don't know what planted the idea in my mind! I have a long torso and a growing collection of shirts that are just barely too short plus some that are just silly lounge arounds that I barely wear. I got it into my head to sort of re-build these into cropped tops for dance class because I always seem to have a shortage of good tops to wear at practice. It's relatively simple to do. Minimal supplies, not a lot of patterning or sewing know-how needed.

Materials:
1 T-shirt
matching/coordinating thread

Tools:
Rotary cutter and cutting mat (preferred)
sewing scissors
sewing machine
soap sliver or chalk


1.Put your shirt on and use a sliver of soap to mark how far under the bust you want to cut the shirt.

2. After marking, lay out your shirt on the ground as flat as possible. Try to match up seams and keep the sides from rippling because of twisted fabric.
3. Go ahead and even up your lines. Make sure the line is not lopsided. One side may be lower than the other because YOU are slightly asymmetrical. If that is the case, use the lowest line and draw across from there.

4. Use scissors/shears to cut along this newly smoothed out line. The line you drew on the front of the shirt should extend around the sides just enough that when you flip the shirt over, you can see the tail ends on each side. This will allow you to connect the tails with a straight line so you know where to cut along the back of your shirt.

**If your shirt is a blousey t-shirt, then you must remove some of the material from the sides and back to make it more fitted. If you don't, it will wrap around to the back and sort of bunch when you tie your rib cage straps. If you like that look, go for it. If not, then:
5. Cut little triangles of fabric off each side under the armhole. Wide bottom of the triangle down, point towards sleeve. If in doubt on amount to remove, slip your half-shirt on and pinch the fabric on either side of your ribs. It doesn't need to be super tight, but evenly distributed between the sides is good. Note how much fabric is pinched. For me this is usually about 2" to the fold on each side.

6. Here's where you have an opportunity to get creative. Simplest option: Make a 4" vertical slit along the center back of your t-shirt. This can be varied by making different types of keyholes instead. Keyholes are especially helpful if you need to remove a little more fabric from the width of your shirt to make it fit snugly. Your keyhole can be a triangle shape with a base and point aimed towards the neck of the shirt or it can be a circle or upside down tear drop shape. Fancier shapes like stars and hearts should be possible but they'll hang funny if they're not reinforced which I won't go into here- you want it fancy, you figure it out ;) If you're not good at free-handing shapes, use a round dish or print a shape from your computer (Microsoft Office software and some of the really basic art programs have shape art).

At this point, you may set aside the top portion of your shirt.

Making the rib cage strap from the bottom half of the shirt:
7. Make sure you have no wrinkles or folds in your lower t-shirt before marking and cutting.
8. Use a ruler or other straight edge and your rotary cutter to cut a perfectly straight line where your original chalk/soap line was drawn. (The idea is to cut off any jagged edges or curves)
9. Measure 4 inches down from your new straight edge and cut with the rotary cutter. You should have a tube of t-shirt material that is 4 inches high and the width of the shirt. Repeat this process one more time.

10. Cut the 2 circles of material to separate each into one long strip. Cut one of them in half to make 2 shorter strips. You now have 3 strips of fabric.

**Note, I also cut the sleeves on the white and blue tops pictured. This is another 'creative opportunity' :D


Sewing your new choli:
**Sew using a stretch stitch (looks like a lightening bolt) or a straight stitch set with a very slight zig zag (just barely moves side to side). This will prevent broken stitches when/if the shirt stretches while you wear it.
11. Sew a short strip on either end of your long strip to make your complete rib cage strap.
12. Sew the sides of your shirt if you cut off triangular pieces of material. If your shirt was fitted to begin with, you should have no side seam sewing to do.
13. Match up center front of the shirt with the middle of your rib cage strap that has been folded in half- it's still as long but now it's 2 inches tall instead of 4 inches. Pin at center front with right sides together and raw edges to the bottom.
**Here you get to decide how fussy you want to be about finishing. I'm not that fussy for this type of project- just an FYI. Knit fabrics don't fray so I'm not bothered by raw edges. There will be some.
14. Starting at center front, stitch rib cage strap to shirt around one side. Sew all the way to the edge of your keyhole opening. Repeat for the other side.

Viola! You now have a brand new dance top made from your favorite band t-shirt or funny slogan shirt :D If you try this out and share pictures somewhere, I'd love for you to leave a link to the pictures or your blog post on the experience in the comments!

Mini Top Hat How-To

Almost a year ago now I created a mini top hat for a quirky dance performance. This morning I was rummaging through my collection of photographs and discovered step by step pictures of the process and thought I should share them already!

Materials:

4 pages of 8.5x11 cardstock

¼ yd fashion fabric

craft glue (I prefer FabriTac)

spray adhesive

paper and fabric scissors (one each, usually)

Printing Pattern:

Print two copies of the page with circular shapes and one copy of the rectangular shape page.

Cut out all pieces of cardstock with one exception. For the second large circle, do not cut out the center of the ‘doughnut’. This is your lower brim and will be left solid.

 

Glue the cardstock down to the back side of the fashion fabric using spray adhesive and then trim the pieces out. Leave yourself a little extra fabric around the edges of the long rectangular piece (the 'stove pipe').

 Use hot glue or fabri-Tac to join the edges of the 'stovepipe' piece into a cylinder. Notch the extra fabric around the bottom and top edge as shown below.

 Use an Xacto blade or scalpel to remove the extra fabric from the middle of the 'brim' piece.

 Fold in the cardstock tabs on the top of the hat and glue them inside the top of the 'stovepipe'. This part will likely require an additional tool like a popsicle stick or butter knife to slide between the top of the hat and the wall of the 'stovepipe' to press the tabs securely to the 'stovepipe' piece.

Next, slide the fabric-and-brim piece over the top of the hat and glue to lower 'stovepipe' tabs of fabric and cardstock. You will be glueing the two 'brim' pieces together as well as you can here.

 Glue down the fabric tabs at the top of the hat and cover with the fabric covered, tab-less top piece (remember, you have two of these?). Carefully trim the fabric that is hanging off the brim. Now would be a good time (while the glue is still super flexible) to start shaping the brim. I chose to finish the edges of my brim with some flexible ribbon stitched over the edge of the two brim pieces.

 At this point you can consider your hat done or go on to add embellishments such as net veils, hat bands and feathers. The best way I've found to keep the little fascinator hat on is with little combed snap clips stitched or glued to the bottom of the hat.

Ahoy Matey!

While working away on the Mord'Sith project for my halloween costume, I was also trying to put together a custom order for a good friend of mine. I was commissioned for the project ages ago but we were plagued by constant delays in obtaining materials so were left scrambling at the last minute. This is a modified version of one of my patterns. I had to change the shapes of the princess seams (and yes, they're called princess seams even in men's clothing) to reflect a masculine shape and the sleeves had to be redrafted and cuffs created. We stayed up til 1am the Thursday before Halloween weekend sewing and doing fittings. Then got up to finish buttonholes at 6am on Friday. The coat is 'coat weight' wool lined with dark sea green rayon lining material. We're probably going to revisit this project at a later date to add extra trim and such for further pirate foppery ;)

She's Only Smiling Because She's Dangerous

Call in the Experts!

Last night's progress on the Mord'Sith costume was all due to my friend Adam who worked at a leather shop some years ago and can often be induced to help out when I find myself in need of leather working. You don't get something for nothing of course. In exchange, I am sewing a fully lined wool pirate coat. Here you see the corset progress as of probably 8pm.

 

After pictures were taken more strap work was completed and I've drafted the thigh guard and holster for tonight's slaving... Incidentally, if anyone wants a copy of these patterns as a starting point, I'm happy to share. You can find the patterns WITHOUT assembly instructions here (click the picture):

Source: Mord'Sith Style Armor via NightLilyDesign on Craftsy